Klipper Log

05:32:47 Klipper: Standby
06:16:36 Klipper: Connecting ...
06:16:36 Klipper: Connected to host
06:16:36 Connected to host via /tmp/printer @0bps
06:16:36 Unable to open config file /home/silveronfire/printer.cfg
06:16:36 Unable to open config file /home/silveronfire/printer.cfg

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
06:16:37 Firmware version: v0.12.0-102-g9f41f53c
06:16:54 Klipper state: Disconnect
06:17:47 Include file '/home/silveronfire/mainsail.cfg' does not exist
06:17:47 Include file '/home/silveronfire/mainsail.cfg' does not exist

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:18:55 Klipper state: Disconnect
06:19:07 Include file '/home/silveronfire/mainsail.cfg' does not exist
06:19:07 Include file '/home/silveronfire/mainsail.cfg' does not exist

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:19:51 Klipper state: Disconnect
06:20:45 Klipper: Disconnected from host
06:20:47 Klipper: Connecting ...
06:20:47 Klipper: Connected to host
06:20:47 Connected to host via /tmp/printer @115200bps
06:20:47 Firmware version: v0.12.0-102-g9f41f53c
06:21:38 Include file '/home/silveronfire/mainsail.cfg' does not exist
06:21:38 Include file '/home/silveronfire/mainsail.cfg' does not exist

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:23:43 Klipper: Disconnected from host
06:23:46 Klipper: Connecting ...
06:23:47 Klipper: Connected to host
06:23:47 Connected to host via /tmp/printer @115200bps
06:23:47 Firmware version: v0.12.0-102-g9f41f53c
06:23:55 Include file '/home/silveronfire/mainsail.cfg' does not exist
06:23:55 Include file '/home/silveronfire/mainsail.cfg' does not exist

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:25:05 Include file '/home/silveronfire/mainsail.cfg' does not exist
06:25:05 Include file '/home/silveronfire/mainsail.cfg' does not exist

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:25:22 Klipper state: Disconnect
06:25:27 Option 'run_current' in section 'tmc2209 stepper_x' must be specified
06:25:27 Option 'run_current' in section 'tmc2209 stepper_x' must be specified

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:29:02 Klipper state: Disconnect
06:29:03 Option 'run_current' in section 'tmc2209 extruder' must be specified
06:29:03 Option 'run_current' in section 'tmc2209 extruder' must be specified

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:30:12 Klipper state: Disconnect
06:30:12 Printer is not ready
06:30:12 Printer is not ready
The klippy host software is attempting to connect. Please
retry in a few moments.
Klipper state: Not ready
06:30:18 Pin 'gpio9' is not a valid pin name on mcu 'mcu'
06:30:18 Pin 'gpio9' is not a valid pin name on mcu 'mcu'

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready
06:34:18 Klipper state: Disconnect
06:34:19 Pin 'gpio9' is not a valid pin name on mcu 'mcu'
06:34:19 Pin 'gpio9' is not a valid pin name on mcu 'mcu'

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Klipper state: Not ready