# Basic Config
esphome:
  name: "mainsmeter"
  friendly_name: Mains
  on_boot: # Set the initial state of the template switch to the actual relay state. This will NOT change the state.
    priority: 250.0 # Wait until WiFi is connected to allow the sensor some time to settle
    then:
      - if:
          condition:
            lambda: 'return id(v_sensor).state > 10;'
          then:
            - switch.turn_on: relay_1
          else:
            - switch.turn_off: relay_1

esp32:
  board: nodemcu-32s

# Enable logging
logger:
  level: INFO

# Enable Home Assistant API
api:

ota:
  - platform: esphome

wifi:
  ssid: "xxxx"
  password: "xxx"
  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:

captive_portal:

time:
  - platform: homeassistant
    id: homeassistant_time

external_components:
  - source:
      type: git
      url: https://github.com/mick96/esphome.git
      ref: cse7761-sonoffpow-fix
    components: [ cse7761 ]

uart:
  tx_pin: GPIO26
  rx_pin: GPIO25
  baud_rate: 38400
  parity: EVEN
  stop_bits: 1

sensor:
  - platform: cse7761
    sonoff_model: POWCT
    update_interval: 5s
    current_1:
      name: Current
      id: a_sensor
      unit_of_measurement: 'A'
      accuracy_decimals: 3
      icon: mdi:current-ac
    voltage:
      name: Voltage
      id: v_sensor
      unit_of_measurement: 'V'
      icon: mdi:sine-wave
    active_power_1:
      name: Power
      id: w_sensor
      icon: mdi:flash
      on_value_range:
        - above: 4.0
          then:
            - light.turn_on: switch_led
        - below: 3.0
          then:
            - light.turn_off: switch_led

  - platform: total_daily_energy
    name: Total Daily Energy
    power_id: w_sensor
    id: kw_sensor
    unit_of_measurement: 'kWh'
    state_class: total_increasing
    device_class: energy
    accuracy_decimals: 3
    icon: mdi:lightning-bolt
    filters:
      # Multiplication factor from W to kW is 0.001
      - multiply: 0.001

  - platform: template
    name: ESP32 Internal Temp
    device_class: temperature
    unit_of_measurement: °C
    id: esp32_temp
    icon: mdi:thermometer
    lambda: return temperatureRead();

  - platform: template
    name: Power Factor
    device_class: power_factor
    id: power_factor
    icon: mdi:angle-acute
    lambda: return id(w_sensor).state / id(v_sensor).state / id(a_sensor).state;

binary_sensor:
  - platform: gpio
    pin: GPIO00
    id: reset
    internal: true
    filters:
      - invert:
      - delayed_off: 10ms
    on_click:
      - max_length: 350ms # short press to toggle the relay
        then:
          switch.toggle: relay_1
      - min_length: 360ms # long press to cycle display info
        max_length: 3s
        then:
          - if:
              condition:
                binary_sensor.is_on: page
              then:
                binary_sensor.template.publish:
                  id: page
                  state: OFF
              else:
                binary_sensor.template.publish:
                  id: page
                  state: ON
  - platform: template # this is a fake sensor to tell the screen which info to show on display
    id: page
    publish_initial_state: true
    internal: true
  - platform: template
    name: Subordinate Device
    id: subordinate_device_on
    lambda: |-
      if (isnan(id(w_sensor).state)) {
        return {};
      } else if (id(w_sensor).state > 4) {
        // Running
        return true;
      } else {
        // Not running
        return false;
      }

display:
  platform: tm1621
  id: tm1621_display
  cs_pin: GPIO17
  data_pin: GPIO05
  read_pin: GPIO23
  write_pin: GPIO18
  lambda: |-
    if (id(page).state) {
      it.display_voltage(true);
      it.display_kwh(false);
      it.printf(0, "%.1f", id(v_sensor).state);
      it.printf(1, "%.1f", id(a_sensor).state);
    } else {  
      it.display_voltage(false);
      it.display_kwh(true);
      it.printf(0, "%.1f", id(kw_sensor).state);
      it.printf(1, "%.1f", id(w_sensor).state);
    }

output:
  - platform: ledc
    id: led
    pin:
      number: GPIO13
      inverted: True

switch:
  - platform: gpio
    pin: GPIO21
    id: relay_1
    restore_mode: RESTORE_DEFAULT_OFF
    on_turn_on:
      - delay: 500ms
      - light.turn_on: switch_led
    on_turn_off:
      - delay: 500ms
      - light.turn_off: switch_led

light:
  - platform: monochromatic
    id: switch_led
    output: led
    internal: True
  - platform: status_led
    id: wifi_status_led
    internal: True
    pin:
      number: GPIO15
      inverted: True